According to the operating instructions, Tomahawk 7010 is not provided for in the alarm system, but its implementation is carried out with the additional connection of the ESM 1 module. This also gives the car owner the opportunity to organize additional engine blocking with a built-in control relay.

[Hide]

Specifications

Review of the main parameters and properties of the Tomahawk 7010 car alarm:

• current consumption when the ignition is turned off - 16 mA;
• the frequency of the radio channel over which packet data is transmitted is 434 MHz;
• a type of modulation used to synchronize the antenna transceiver with the remote control - FM;
• operating range of the key fob (pager, communicator) - 1.2 km;
• the duration of signals for controlling the central locking (CL) ranges from 0.8 to 30 seconds and is programmed by the user in accordance with the manual;
• using feedback to connect the remote control to the car alarm control unit;
• To power the side optics, two outputs designed for 7.5 A are used, sirens - 1.5 A, central locking - 15 A.

The Tomahawk 7010 can be used on passenger vehicles with an operating voltage of +12 volts in the on-board network.

Equipment

Description of parts and devices included in the Tomahawk 7010 security system:

1. The control module, equipped with a microprocessor, is housed in a black plastic case with model markings.
2. Main pager, with built-in feedback system and display. Data on the vehicle's status and security are displayed on the screen.
3. An additional keychain that allows you to perform almost all functions. This device does not have a display.
4. Sensor for detecting external influences and impacts on the car body. Incorrect settings or a faulty state of the regulator will lead to false activation of the siren and alarm mode.
5. LED lamp. Designed to determine the state of the anti-theft complex.
6. Transceiver with antenna module and connection cable.
7. A set of wires for mounting and connecting the components of the security system to the control unit and battery.
8. Service manual for using and setting up an anti-theft installation.
9. Limit switch to protect the engine compartment or luggage compartment. This device is push-button.
10. Box.
11. Buyer's Reminder. The document specifies the nuances regarding product maintenance.
12. Warranty card.

The manufacturer did not include a siren and door limit switches in the Tomahawk 7010 alarm package, so these elements should be purchased additionally.

Channel “130” in the video briefly talked about the configuration of the 7010 anti-theft systems.

Key Features

Description of the main functions and features of the Tomahawk 7010:

1. The complex is equipped with a signal anti-scanner. It is designed to protect transmitted pulses from interception and scanning. The developer claims that hacking the alarm is impossible.
2. Availability of a non-volatile memory module in the control unit. This allows you to save alarm information when the power is turned off. Further activation of the battery will cause the system to return to its original state.
3. Using a two-level touch shock sensor. The device allows you to determine not only physical impacts on the body, but also movement near the vehicle. All information is transmitted to the remote control with a screen.
4. Panic function. Its operating principle is to activate the car's headlights and alarms when receiving a command from the pager. The option helps scare away possible intruders from the car.
5. Automatic reset to security mode. This function allows you to restore vehicle protection if it is accidentally disabled.
6. Bypassing non-working security zones. When set to protection, the alarm monitors the state of all elements connected to the control unit. Data about this is displayed on the key fob display.
7. "Search for a car." Activating the option causes the lights to blink when receiving a corresponding command from the pager. This allows you to find a vehicle left in a large parking lot.
8. Determination of low battery in the key fob. The status indication is shown on the screen in the form of a battery icon, just like on mobile phones. This allows the car owner to timely determine the failure of the battery and replace it.
9. Use of additional channels. They are intended to control electrical equipment such as power windows, sunroof, seat adjustment, and folding mirrors. It is also possible to control the operation of the trunk door lock. The function is user programmable.
10. Activating the security mode on a car with the engine running.
11. Possibility of connecting additional sensors and regulators.
12. Two-step security deactivation. The user can configure the security mode control using the remote control and an individual password.
13. Possibility of remote shutdown of the shock regulator and additional devices. The user can deactivate only one zone of sensor operation - the warning zone, and leave the alarm zone.
14. Delay for turning off the light in the car interior. The user independently sets the interval at which the lighting will work for a certain time after turning off the ignition and activating the security function.
15. Blocking the car engine when setting protection. Activation and deactivation of the option is carried out using relays with normally closed and open contacts. In one state the device works, in another it does not.
16. Built-in central locking (CL), providing additional security for the machine.
17. Using a relay to connect car lighting devices.
18. Possibility of separate control of central locking on a vehicle with the engine running.
19. The “Anti-robbery” function blocks the operation of the engine during a robbery attack on a car. The alarm automatically recognizes a power grab based on readings from the handbrake and pedal sensors. The engine stops automatically after a gap that will allow the criminal to move away to a safe distance from the user. The time is configured by the consumer and can range from 30 to 60 seconds. This allows you to protect the car owner.
20. Using a personal code to gain access to the service mode and security functions.
21. Warning the car owner about unlocked doors before driving.
22. Possibility of using the standard steering horn to play alarm signals. The option is programmed during installation. The horn can be configured to work together with a siren or without it.

Advantages and disadvantages

List of main advantages of the system:

• application of an interactive method of encryption of transmitted signals;
• advanced functionality at a price affordable for most consumers;
• clear service manual for maintenance and connection in Russian.

According to consumer reviews, the main disadvantage of the Tomahawk 7010 alarm system is the rapid failure of the pager battery. When setting up the system for the first time and programming options, discharge occurs much faster.

Differences between TZ-7010 and TW-7010

Alarms Tomahawk TZ-7010 and TW-7010 have the same functions; the significant difference between these models is only in the design of the communicators.

Pagers for controlling these systems have minor differences in terms of design. But these devices are interchangeable and can be used in similar systems without loss of functionality.

How to install Tomahawk 7010?

Alarm Installation Guide 7010:

1. The system control unit is hidden inside the cabin. The device can be placed behind the instrument cluster, radio or under the control panel. Fixation is carried out on a flat surface using clamps or self-tapping screws. To eliminate the effects of vibration and moisture, the module can be wrapped in foam rubber and cellophane.
2. A siren is located under the hood if it was purchased additionally. For fixation, a bracket is used, which must be screwed to the car body. The siren is mounted away from the cylinder block and other metal surfaces and parts adjacent to the body.
3. An “Override” service mode button is installed under the instrument panel. To hide this element, you can additionally wrap it with electrical tape of a standard color.
4. A transceiver with an antenna adapter is placed on the windshield. It is recommended to place it away from electronic circuits and metal parts. Do not install the device on the top of the glass if a tint film is applied to it.
5. A limit switch is installed on the hood. The wire from it must be routed to the control module through the technological hole separating the interior from the engine compartment. It is not allowed to install the device in a place where there is a drain.
6. The shock sensor is located in the central part of the car body. To fix it, a flat metal surface is used without plastic or rubber gaskets.
7. After installation, all alarm components are connected to the control unit. Wires should not be laid near electronic devices or spark plug power circuits.

Connection card for the main 14-pin connector

The connection of the main block of the system control unit must be carried out in accordance with the diagram:

Color	Description
Red	The car alarm power supply must be connected directly to the positive terminal of the battery. The electrical circuit must be protected by a 15 amp fuse device.
Black-green	Positive contact output for the rotating optics relay
Black	Negative clamp. It must be connected to the car body or the negative terminal of the battery directly. When grounding, the strongest possible contact must be ensured.
Yellow-green	Positive output of the side or turning optics relay, the circuit must be equipped with a 7.5 ampere fuse
Blue	Negative terminal for connecting courtesy lighting or power window control
Yellow	Positive input of the ignition switch
Black and yellow	Negative output for connecting the starter blocking relay
Grey	Positive contact for connection to siren or steering horn
Red-yellow	Not used
Black and yellow	Negative pin for implementing an additional channel
Red-blue	Positive contact for connecting door lock limit switches
Black and blue	Minus of triggers
White-orange	"Limit switch" of the luggage compartment
Gray-orange	Hood limit switch negative terminal

User manual

According to the operating instructions, before using the Tomahawk 7010 alarm system, you must ensure that the system is connected correctly. You should activate the security mode and make sure the door locks are locked.

Key fob control

To control the key fob, you need to install a working battery in the device. The battery is inserted into the compartment located under the rear protective cover of the immobilizer.

The Tomahawk 7010 alarm control unit can work with no more than four key fobs. When adding new communicators, information about old remote controls is erased from the microprocessor memory.

How to program the key fob?

Binding a new remote control, in accordance with the operating instructions for the Tomahawk 7010 alarm system:

1. When the ignition is turned off, the key in the lock is turned to the “Off” position.
2. The button to enter the service mode is “clicked” seven times. The driver must be in his seat in the car at this moment.
3. The key is turned in the lock to turn on the ignition. The siren or steering horn will sound seven times, this indicates that the system has entered the remote control programming menu.
4. On the main communicator, press keys 3 and 4 simultaneously. The controls are held until the sound signals are played. This indicates that information about the pager has been successfully registered in the memory of the microprocessor device.
5. To exit the programming menu, you must not take any binding actions for 60 seconds. The alarm will automatically return to its original state.

The steps of turning the ignition off and on, pressing the service button and binding are repeated for each device.

Designation of symbols and buttons on the key fob

Indication of icons on the main pager screen:

Main communicator display

Description of elements:

1. The option to block keys on the device is enabled.
2. The hourly engine autostart mode is activated.
3. Blocking the power unit.
4. The automatic arming function is enabled.
5. The vehicle's ignition system is activated.
6. Engine running.
7. The luggage compartment lock is open.
8. The anti-robbery mode on the vehicle is enabled.
9. Alarm option as a result of a strong impact on the body.
10. Car servicing.
11. Shock sensor warning zone.
12. Disable sensitivity controller.
13. Indication of the connection between the pager and the microprocessor unit.
14. Vehicle security mode with confirmation signals enabled or disabled.
15. The car door locks are locked or unlocked.
16. Sensitivity controller main zone disable icon.
17. Battery charge in the key fob.

Correspondence of keys on Tomahawk 7010 communicators

Autorun

To prepare the vehicle for setting up the remote start option, do the following:

1. On a car with the engine running, the transmission selector is switched to neutral or “Parking” mode.
2. The handbrake lever is raised.
3. The key is pulled out of the ignition. The motor remains running.
4. The user gets out of the car and locks all the doors. The power unit should stop randomly.

How to set up autorun?

On vehicles with an automatic transmission, the setting is as follows:

1. On the pager, press and hold button 2. This control must be released after the remote control plays a melodic signal.
2. When using an additional key fob, the LED will change color from red to green. At this moment or after the melody, the user must briefly press button 2. The car’s power unit will start, the pager will play a signal, and the car’s headlights will flash.
3. The engine will turn off automatically after a user-programmed time. After starting the engine, an indicator in the form of a vehicle with smoke from the muffler will appear on the communicator screen.

To start the power unit on a car with a manual transmission, perform the following steps:

1. On the pager, press and hold button 1.
2. The control element is released when a melodic signal is played. When using a spare communicator, the LED will change color.
3. The first key is “clicked” again.

User Evgeniy Vakshin spoke about the features of setting up the autostart function on Tomahawk anti-theft systems.

Security mode

Features of protective function control:

1. To turn on, use button 1. All door locks will close, the car's headlights will blink and the siren will sound. Disabling the security mode is done by pressing the second key.
2. To activate protection without sound alerts, control element 4 is used. If the siren is activated, information about this will be displayed only on the remote control screen.
3. If you need to activate security on a car with the engine running, the engine should be started in advance. The driver needs to lock all the locks, and then “click” the first button. Then, within three seconds, the user must press the same button again. When the security system is turned on, the side lights will blink and the siren will sound.

If the pager breaks down, the protection is activated using the service key:

1. The car door is opened with the key, as a result of which the siren will sound. The ignition turns on.
2. The service mode entry button is pressed three times.
3. The key in the lock is turned to the “Off” position. The siren and side lights of the car will sound.
4. After 20 seconds the security will be activated. The user must have time to leave the car during this time and lock all the doors.

Entering and changing your password

Initially, the alarm is assigned code 11.

To enter it when the system is turned off, perform the following steps:

1. The car door opens and the ignition is activated.
2. The service mode entry button is pressed once (if the standard password is used).
3. The key is turned to the "ACC" position. The “Override” key is “clicked” again (this is the second digit of the 1st password).
4. The ignition is turned off.

To change the individual code of Tomahawk 7010, perform the following steps:

1. After turning off the ignition in the car, press the button to enter the service mode 4 times.
2. The key in the lock is turned to the “ACC” position. The anti-theft siren plays 4 beeps.
3. The “Override” key is pressed once, as a result of which the alarm will enter the code setting mode. To enter a password, characters from 1 to 4 can be used; they are indicated by buttons in accordance with their numbers. If the first digit of the password is accepted, the siren will sound.
4. To specify the next character, you need to “click” once on the service key. The input steps are similar.

Download free installation and operating instructions in PDF format

You can download technical documentation for installation and configuration of the Tomahawk 7010 security complex using the following links:

Errors in device operation and their elimination

Overview of malfunctions and malfunctions that may occur during the operation of the Tomahawk 7010:

1. The security system does not respond to commands sent from the remote control. The user must diagnose the power supply in the device. If the battery needs to be replaced, be sure to pay attention to the polarity during installation. After dismantling the element, press button 5.
2. If there is no response to commands, the cause of the problem may be damage to the board or contact elements on the communicator keys. To repair, the user will need to disassemble the device by unscrewing the bolts on its body and check the circuit. If traces of moisture are visible on it, then the communicator must be dried in a warm place, but not near a household stove or in the sun. Failed contacts must be resoldered or cleaned if the problem is their oxidation. Remove dust and debris from the housing with a dry brush or cloth.
3. Incorrect operation of the alarm and lack of response may result from damaged cables. When the insulating layer wears out or breaks, the system does not close all doors or does not respond at all to the pager command. A multimeter is used to diagnose the integrity of electrical circuits. When checking, you must first assess the condition of the lines that are laid in the area of ​​the moving nodes. When laying new wires, it is recommended to wrap them with electrical tape to ensure maximum reliability in the future.
4. The cause of the malfunction may be poor contact of one of the alarm blocks with the control unit. It is necessary to diagnose the connectors for connecting the microprocessor, transceiver, and push-button switches. The contact elements may have become clogged or oxidized and will require cleaning to correct the problem. If the plug itself fails, it must be replaced.
5. A large number of false alarms may be due to incorrect settings of the sensitivity of the shock regulator. To change this parameter, special control devices located directly on the sensor are used.
6. If it was not possible to find the reason for the incorrect operation of the alarm, then it may be a malfunction of the microprocessor. The device could fail due to moisture getting inside. The steps to troubleshoot the problem are the same as in the case of a pager. If visual diagnostics did not allow us to identify the problem, then we can conclude that it is a software malfunction. To eliminate it, you will need to reflash the control unit or repair it.

How much does Tomahawk 7010 cost?

You can buy model 7010 at this price:

Video

Sergey Yashchenko in his video showed the process of hacking the Tomahawk anti-theft system using a code grabber.

Ratings - 5, average score: 4.2 ()

User manual Tomahawk, model TW-7010

Fragment of instructions

The side lights will flash once and the LED will begin to blink. For the operating steps and procedure for disabling the Anti-Hijack mode, see paragraph 16 "Remote Anti-Hijack" LCD display indication: (f HIJACK 12 More information about the TOMAHAWK TW-7010 car alarm on the website Chapter TOMAHAWK TW-7010 16. Remote Anti-Hijack. Function used to return the car in the event of a violent seizure. To activate this function, you must press and hold two buttons and key fobs simultaneously with the ignition on. The side lights will flash 1 time, the system LED will begin to blink. The remote Anti-Hijack has 3 stages of operation: Stage 1: First 30 seconds after activating the Anti-Hijack mode, the system does not manifest itself in any way, the security complex allows the attacker to move away from you somewhat. Attention! At the first stage, it is possible to disable the mode from the key fob, to do this you need to press the button or hold the "OVERRIDE" button for 3 -x sec. Stage II: For the next 30 seconds, the siren emits warning “CHIRPS” and the parking lights flash. Stage III: The final stage occurs after approximately 60 seconds. after activating the Anti-Hijack mode. The siren will sound and the engine will be locked. Attention! To disable the Anti-Hijack mode at stages II and III: 1. Turn on the ignition. 2. Press and hold the button. OVERRIDE for 3 seconds. (the siren will sound “CHIRP”) 3. Turn off the ignition. 4. Anti-hijack mode will be disabled. The system will remain in armed mode. If a PIN code is programmed, disabling the “Anti-hijack” mode can only be done by entering the PIN code. LCD display indication: (fSHASK 17. Valet mode. Valet mode is used by the car owner if the car is transferred to third parties, for example, for maintenance. After activating this mode, the system can only perform service functions such as controlling an additional channel or central locking Turning on and off the Valet mode is done when the security is turned off by holding the button until the key fob-pager sounds a sound signal (or the color of the LED on the additional key fob changes to green) and then pressing the button, or by holding the "OVERRIDE" button for 3 sec., with the ignition on. The activation of the Valet mode will be confirmed. More information about the TOMAHAWK TW-7010 car alarm on the website 13 G/L TOMAHAWK TW-7010 with 4 flashes of parking lights and 4 “CHIRPS” of the siren, the LED will be constantly on. Indication LCD display: z1zz 18.3 protection against false alarms The Tomahawk TW-7010 security system is a highly intelligent car security device, so the system uses a complex, multi-level algorithm for protecting false alarms. First level. When the security mode is turned on, the main unit tests all security zones; if any sensor is found to be defective, the system automatically turns it off and notifies you about this using 4 “CHIRPS” of the siren. LCD display indication: icon of the corresponding trigger. Second level. During the security mode, the system analyzes the operation of the sensors; if the shock sensor or additional sensor is triggered 8 times in a row, it will be disabled. 19. Remote polling of the status To perform a remote polling of the vehicle’s status, press the 1|K button. The parking lights will flash three times, the key fob pager will display the car's status. Attention If after pressing the button. 1|E (or any other button) within 3 seconds there is no confirmation of the command execution and the key fob pager emits 1 “Beep”, which means the vehicle is outside the range of the key fob pager transmitter. 20. Remote trunk release (additional channel). To implement this function on many vehicles, additional equipment must be installed. If this option is enabled, then to unlock the trunk, you must press and hold the key||E key of the key fob until the key fob sounds a beep (or the color of the LED on the additional key fob changes to green) and then press the key. . Execution of the command will be accompanied by 3 flashes of parking lights and “CHIRPS” of the siren. Attention If the system was armed when the trunk was unlocked, the shock sensor and trunk trigger will be disabled until the trunk is closed. More information about the TOMAHAWK TW-7010 car alarm on the TOMAHAWK TW-7010 website LCD display indication: 21. Remote siren deactivation. In many countries, the use of car alarm sirens at night is prohibited (for example, in Moscow after 23°°), so the security system provides for turning off the siren from the key fob. To do this, the system must be in security mode, then press the button. (p. LCD display indication: In this case, the system will be fully operational, with the exception of the sound warning from the siren. All information will be displayed on the LCD key fob display. The siren is turned on by pressing the button once ((T|. LCD display indication: (("^ 22 .Additional channel control.Additional...

The Tomahawk 7010 anti-theft system belongs to the class of high-tech systems that have no analogues on the domestic market. The instructions for the Tomahawk 7010 allow you to independently connect the alarm, configure basic functions or troubleshoot problems that have arisen.

[Hide]

Specifications

Description of the main parameters of the Tomahawk 7010 car alarm:

1. To supply power to the car security system, a 12-volt power supply is used. The use of alarms on heavy trucks and other vehicles where the voltage is 18–24 volts is not permitted.
2. When the ignition is turned off and the protection mode is activated, the amount of current consumed by the system will be no more than 16 mA.
3. The permissible current for power supply circuits and relay contact elements is no more than 15 amperes.
4. To provide power to the contact elements of the remote blocking relay, no more than 30 amperes of current will be required.
5. The siren is powered via a gray cable, the output current value will be no more than 1.5 amperes.
6. Additional channels are powered via a black-yellow cable, which requires no more than 300 mA of current. The same amount of current is needed to connect the polite lighting system and the engine blocking relay.
7. To power the alarm lights, approximately 7.5 amps will be required for each optical device.

Equipment

The basic signaling kit includes:

1. Main electronic control module. The device is designed to receive, process and transmit pulse data with a communicator. It is supplied to the market in a black plastic case, on which the name and brand of the model are applied.
2. Main communicator. The device is equipped with a screen that displays information regarding the status of the alarm.
3. Spare pager. Does not have a display or feedback function.
4. Shock regulator. Necessary to determine the physical impact on the car body. When installing, it is important to set the sensitivity correctly to prevent false alarms.
5. LED indicator of signaling status.
6. Transceiver module.
7. Mounting kit of wires for connecting an electronic module, transceiver, central locking and other devices.
8. User's manual for installation and use of Tomahawk 7010. The service manual describes all the functions and nuances regarding the operation of the security complex.
9. One limit switch. The device belongs to the push-button category.
10. Package.

Door limit switches and a siren will have to be purchased separately, since these devices are not included in the package.

Alarm equipment Tomahawk TW-7010

Key Features

Features of the Tomahawk 7010 security system:

1. The presence of an anti-grabber and an anti-scanner ensures reliable transmission of signals between the electronic module and the communicator without the possibility of interception. According to the manufacturer, no modern scanner or code grabber can intercept pulses.
2. The electronic signaling unit is equipped with a non-volatile status memory module. Thanks to this, when the battery is disconnected and then turned on again, the alarm will return to its original state.
3. Availability of an integrated two-level touch controller. Its use allows you to determine the physical impact and send information about this to the car owner’s remote control.
4. Panic option. With its help, the car owner can activate the siren and optical devices for a certain time. This will scare away strangers who are near the car.
5. Option to automatically re-set to protection mode.
6. Ability to bypass non-working areas. If one of the security zones refuses to work for certain reasons, the alarm will automatically bypass it. Information about the problem area will be sent to the communicator.
7. Availability of protection against false inclusions. If the motion controller is set correctly, the alarm will not go off without a reason.
8. Option to search for a car in the parking lot. When it is turned on, the car's optical devices will blink, which allows the car owner to determine the location of the car in a large parking lot.
9. Availability of a low battery indication system in the pager. The communicator screen displays the battery charge level. Thanks to this, the consumer will be able to promptly replace the power source in order to prevent problems in the operation of the Tomahawk 7010.
10. Availability of an additional control channel. This channel is programmable.
11. Possibility of turning on the protection mode when the power unit is running.
12. The electronic alarm module is equipped with several connectors. An additional controller can be connected to one of them.
13. The central locking control time interval can be programmed. The setting time is 0.8, 10 or 30 seconds.
14. Two-stage opening of door locks and disabling the security mode.
15. Temporary deactivation of the sensitivity controller, as well as additional controls.
16. Possibility of delaying the switching on of interior lighting. The function is programmable and can be set to different time intervals.
17. Function of remote unlocking of the tailgate. The option is configurable.
18. Possibility of blocking the power unit. The function is set via a normally closed or open relay.
19. Availability of a built-in relay for connecting optical devices. For this, two additional channels are used.
20. Availability of built-in central locking. Provides additional vehicle protection.
21. Possibility of controlling the central locking when the power unit is running.
22. Built-in engine blocker. Allows you to block the operation of the power unit in case of unauthorized access to the car.
23. The main communicator screen graphically displays the operation of all activated triggers. Also, using the display, the consumer can find out about the protection status of the machine.
24. Anti-hijack mode or anti-robbery function. This option is designed to protect the car owner from robbery and is intelligent. If the machine is grabbed forcefully and the option is configured correctly, the engine will be blocked. The blocking process will begin after a certain time, when the attacker moves away to a safe distance from the owner of the car.
25. Using a personal password. The code is used to activate or disable the anti-theft function, as well as control basic options.
26. Availability of a memory module for car alarm activations. The communicator display shows complete information regarding the activation of alarm signals. Also, using the screen, the consumer can find out about the zones that were triggered and led to the activation of the alarm mode.
27. Option to warn the car owner about an unlocked door when starting to drive.
28. Increased range of the communicator. Ideally, this parameter is 1200 meters. But in fact it will be less. Its operation is affected by weather conditions, architectural features of the area, as well as interference. If they are present, the range of the communicator will be reduced several times.
29. The car owner has the opportunity to connect a standard horn. This feature is programmable.
30. If necessary, the consumer can install and connect an additional remote engine start module. Depending on the module, the start procedure can be implemented by command, air temperature or timer.
31. Availability of a comfort system. If your car has power windows and a sunroof, you can set these devices to close automatically when the protection mode is turned on.

Channel 130 presented a brief overview of the Tomahawk 7010 anti-theft system.

Advantages and disadvantages

Advantages of Tomahawk 7010:

1. Effective protection thanks to the use of interactive signal coding. According to reviews, consumers do not encounter the problem of electronic hacking.
2. The presence of feedback provides the ability to constantly monitor the status of the alarm in real time.
3. Wide functionality at a relatively low cost. Tomahawk 7010 alarms are characterized by the presence of many useful functions that simplify the use and configuration of systems.
4. Clear and convenient operating and installation instructions. With the help of service documentation, the consumer has the opportunity to independently install and connect all signaling components. Of course, this will require certain experience and skills. But in their absence, it is quite possible to complete the task yourself.

The main disadvantages of the Tomahawk 7010 include the rapid drainage of the battery in the remote control. When setting up the alarm, as well as intensive use, the battery may discharge. If this happens on the road, where it is impossible to buy a battery, then you will have to control the system using the service mode.

How to install?

The alarm installation procedure begins with studying the circuit; when connecting, you should take into account the following nuances:

1. Electrical circuits should be laid away from electronic devices. Their presence may cause interference when sending commands.
2. Cables should not be laid in places where there are moving body parts. If they are damaged, it will be difficult to detect the problem.
3. The installation of all main system devices should be carried out away from power electrical circuits and components. We are talking about ignition coils, high-voltage cables to which the spark plugs are connected, etc.
4. Before installing the security complex, you can connect all the elements according to the diagram and connect them to the battery. This will allow you to verify in advance that the alarm is in working condition.
5. If the car is equipped with airbags and a radio with a code, then disconnecting the battery is not recommended. When you connect it further, the audio system will ask for a code, so we recommend that you refer to the service manual in advance.
6. All electronic modules and devices are connected only after they have been installed.

General installation map of Tomahawk 7010

The installation procedure is as follows:

1. The electronic module of the system is installed away from sources of interference, moisture and heat. We are talking about electronic devices, as well as the heating system. If this requirement is not taken into account, the operation of the unit may be disrupted. The module is installed with the connector down to prevent drops of condensation from flowing down the wires into the device onto the board. For installation, you should choose the most hidden place, for example, behind the instrument panel or in the free space behind the center console. The module is fixed using self-tapping screws, double-sided tape or plastic ties. The block must be secured as securely as possible to prevent it from being damaged by vibrations during movement.
2. The siren is installed in the engine compartment. It is not included in the package, so it can not be installed, but an alarm without a siren is virtually useless. The device is mounted with the horn down, this will avoid the accumulation of moisture inside the device. If the siren is autonomous, that is, equipped with a built-in battery, then during installation it is necessary to ensure free access to the keyhole. The siren must be installed away from the cylinder block and sources of moisture to avoid the negative effects of high temperatures. The installation must be performed in such a way that intruders do not have access from under the bottom of the car to the device and its connection wires.
3. The transceiver module is mounted on the inside of the windshield, away from electronic devices and metal parts. The distance between them and the antenna should be at least 5 cm, this will avoid possible interference. Installation is carried out on a cleaned and degreased surface. It is not recommended to install the module under the tint film or at the bottom of the glass, this will lead to poor signal transmission.
4. The limit switch is installed on the hood of the car. When the hood is closed, there should be no access to the switch; this must be taken into account during installation. If you purchased additional limit switches, they are installed on the luggage compartment, as well as on the doors. For installation you will need to make holes in the metal.
5. Installation of the Valet service button is carried out in a place inaccessible to the criminal, since it can be used to disable the alarm. To hide the button, you can disguise it under one of the standard wiring harnesses by wrapping it with electrical tape. The button must be positioned so that the car owner has easy access to it from the driver’s seat.
6. The shock sensor is securely fixed in the central part of the body to metal. There should be no plastic or rubber gaskets between it and the surface, this will lead to a deterioration in the sensitivity parameter. The device is fixed with bolts, self-tapping screws or double-sided tape.
7. The alarm status LED light is installed on the dashboard. It must be installed so that the flickering of the diode is visible from the street. This will designate the vehicle as protected.
8. When all components are installed and secured, they are connected to the battery and electronic module. Electrical lines are laid under the plastic upholstery, in particular, under the sills. When laying the wires, we recommend additionally wrapping them with electrical tape. This will provide reliable protection from external influences. In addition, in the event of a break-in, detecting the wiring of the anti-theft complex will be problematic.

User manual

The instructions for the Tomahawk 7010 include a description of the use of all functions and modes.

Designations of buttons and symbols on the key fob

The designation of the buttons on the key fob and their functional combinations are shown in the photo:

Tomahawk 7010 main options programming table

Changing your personal password

The procedure for changing the PIN code is as follows:

1. The ignition system is turned off; for this, the key is set to Off mode.
2. Emergency key Override Clicks four times.
3. The procedure for turning on the ignition is carried out; in confirmation, the siren will emit four sound pulses.
4. Then the service button is pressed again, this will activate the password setting function. Using the key fob, the car owner enters a new PIN code; numbers from 1 to 4 are allowed. If the number is 1, then the button with a locked lock is pressed, if 2, then with an open lock, if 3, then a key in the form of an open trunk is pressed. To enter number 4 of the password combination, click the button with the crossed out speaker. The successful assignment of the first digit of the password will be indicated by sound signals from the siren.
5. To go to the menu for setting the second digit of the password, the Override key is clicked once. To enter the next digit, the same conditions are taken into account as for assigning the first one. The siren will emit a beep as confirmation. After entering the password, we recommend writing it down on a separate piece of paper so as not to forget.

Emergency shutdown and activation

If the communicator breaks down or is lost, the procedure for emergency deactivation of the protection mode is performed as follows:

1. If the car door lock is opened with a key, this will trigger alarms. The key is inserted into the ignition and switched to ACC mode.
2. The Override service element is clicked three times.
3. The ignition is turned off. The siren speaker will emit one beep. The car's optical instruments will blink.
4. After twenty seconds, the protection mode will be activated. The door locks will not be locked; they must be closed independently from inside the car or using a key.

To enable the protection mode, similar steps are performed. The only difference is that the security will be activated without a 20-second interval.

The new generation car alarm tomahawk tw 7010 is a high-tech device that meets all modern safety requirements. Despite its low cost, the alarm system has practically no analogues and is very easy to use.

The presence of many convenient services is complemented by a two-way communication system, which ensures reliable contact between the key fob and the car at a distance of up to 1.2 km.

Alarm description

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline!

The tomahawk tw 7010 protective system is installed in any vehicle whose on-board voltage is 12V.

The turbo timer mode allows the turbine to cool down gradually after turning off the engine, which allows you to spare power plants equipped with turbocharging.

All types of transmissions are supported by selecting the appropriate mode. Any details related to the operation of the security system are contained in the instructions that come with the alarm.

Remote control key fobs

Tomahawk tw 7010 protection is equipped with two key fobs at once. The main key fob, equipped with a TFT screen, displays information about the security system; an auxiliary waterproof key fob is also provided.

The key fob is a remote control that runs on a regular AAA-1.5V battery; battery life directly depends on the conditions of use. You can monitor the battery charge level using the appropriate indicator. The battery should be changed promptly!

The key fob itself is equipped with five control keys and an LCD display. After pressing each button, the microprocessor generates a command, which is transmitted via a radio channel to the head unit of the security system, where it is processed and executed.

There is protection (anti-grabber) that changes the transmitted code each time, preventing attackers from recording the command.

When the command is completed, the central unit sends a corresponding signal to the key fob, which notifies the user about this through various icons.

How to use the security complex

The Tomahawk tw 7010 security system is turned on by pressing the corresponding key once. At the same time, the vehicle's side lights will flash and a single warning signal will be heard (unless silent mode is turned on).

All doors, trunk and hood will be closed and the central LED will start flashing.

Attention! If the immobilizer function is active, put the vehicle into security mode very carefully. If instead of a single beep you hear a double beep, it means the immobilizer has been disabled.

Turn it on again. Follow the indicators on the key fob display. More detailed instructions on using the security system are contained in the operating instructions.

Attention! If, when the tomahawk tw 7010 security system is turned on, one of the triggers is in an active state (for example, one of the doors is open), the system will notify you of this with four short beeps and the parking lights will flash four times.

USER MANUAL AND INSTALLATION INSTRUCTIONS CAR ALARM TOMAHAWK TW-7010 Find new versions of instructions on the website http://intorg.ru TOMAHAWK TW-7010 CONTENTS: OPERATION MANUAL. I. II. III. IV. V. Main functions of the system. LCD display indication. Remote control key fobs. Functions performed using the key fob. How to use the security system: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. Arming. Quiet arming. Disabling the shock sensor and additional sensor. Disabling security mode. Two-step disabling the security mode. Security with the engine running. Automatic arming. Automatic re-arming. Security mode. Immobilizer mode. Safe driving function. Central locking control while driving. Search for a car. Panic function. Anti-Hijack. Remote Anti-Hijack. Valet mode. Protection against false positives. Remote status polling. Remote trunk release. Remote siren deactivation. Additional channel management. Emergency arming/disarming. Personal code (PIN code). Programming a new PIN code. Programming new key fobs. Information about programmed key fobs. Information about the performance of sensors. Displaying information on the LCD key fob. Functionality of the key fob pager. LED indication. The procedure for replacing the battery in a key fob with an LCD display. Function programming mode. Reset to factory settings. VI. Programming table. Description of programmable functions 3 4 7 8 9 9 9 9 9 10 10 10 11 11 11 12 12 12 12 12 13 13 14 14 14 15 15 15 16 16 18 18 18 19 18 20 20 20 21 22 23 More information about car alarms TOMAHAWK TW- 7010 on the website http://intorg.ru 1 TOMAHAWK TW-7010 INSTALLATION MANUAL. I. II. III. IV. V.VI. Basic principles of installation. Selecting the location of the main blocks. Connecting the system. Scheme. Technical data. Equipment. 25 25 26 28 35 36 You have purchased a professional anti-theft alarm system. This security complex is manufactured with the greatest care, using the latest achievements and technologies. The alarm system will provide your car with reliable protection from the attacks of car thieves and robbers, thanks to the latest technologies. You will be able to fully control the situation inside and around your “pet”. The wide service functions of the security complex will reveal new capabilities of the car. 2 More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 OPERATION MANUAL I. Basic functions of the system. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. Anti-grabber. Anti-scanner. Non-volatile memory allows the system to retain its state in the event of a temporary power failure. Two-level shock sensor. Two-level additional sensor. Panic mode. Automatic reset to security mode. Valet mode. Bypass the faulty zone. Protection against false positives. Programmable key fobs. Search for a car. Low battery indication. Programmable additional control channel. Security mode with the engine running. Disabling the siren from the key fob. Programmable impulse of the central locking. Two-step disabling the security mode. Temporarily disable the shock sensor and additional sensor. Interior lighting delay accounting function. Remote status polling. Remote trunk opening (optional). Engine blocking (programmable NC/NO). Built-in parking light relay (two channels). Built-in central locking. Central locking control when the engine is running. Built-in immobilizer. Graphic indication of all triggers and system status on the key fob with LCD display. Polite backlight function (optional). Anti-Hijack mode - protection against robbery. Individual PIN code. Memory of system activation. Warning function about an open door while driving. Increased range of LCD key fob up to 1200m. (depending on external conditions). Ability to connect a standard horn (programmed) Ability to control the comfort system. Information about programmed key fobs. Displays changes in system status on all programmed key fobs with an LCD display. Built-in clock (LCD key fob). Built-in timer (LCD key fob). Built-in alarm clock (LCD key fob). Key fob pager button locking function. Read more about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 3 TOMAHAWK TW-7010 II. LCD display indication. 1-1 Z Z Z HIJACK PASS AM PM Fig. 1 4 1. - indication of the security mode. 2. - indication of the “silent security” mode. 3. - indication of a closed central lock. 4. -indication of an open central lock. 5. - indication of open door(s). 6. - open hood indication. 7. - open trunk indication. 9. - indication of the operation of the key fob-pager transmitter. More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 10. - indication of a weak impact. 11. - indication of a strong impact. PASS 12. - indication of shutdown of the warning zone of the shock sensor. PASS 13. 14. 15. - indication of shutdown of the main shock sensor zone. HIJACK 1-1 Z Z Z - indication of the “Anti-hijack” mode. - indication of the “Valet” mode 16. - indication of the disabled hand brake 17. - indication of the battery charge level. 18. - indication of the ignition on. 19. - indication of key fob-pager button locking. 20. - indication of the activated immobilizer. 21. - indication of the activated automatic arming mode. 22. - indication of the enabled timer. Read more about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 5 TOMAHAWK TW-7010 23. - indication of the alarm clock on. AM 24. PM 6 - hours. Read more about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 III. Remote control key fobs. The security complex can be equipped with two types of key fobs. A key fob with an LCD display displays information about the vehicle's status using icons. The standard type keychain is waterproof (spare). F LCD Fig. 2 LED Fig. 3 The remote control (Fig. 2) is a miniature transceiver powered by an AAA-1.5V battery; battery life depends on operating conditions. A special indication is provided to monitor the battery charge level (see page 5). Don't forget to change the battery in advance! The key fob has five control buttons: kn. , book , book , book , book and liquid crystal display. When you press one button or a combination of buttons, the built-in processor generates a coded command for execution by the main unit. Each subsequent code is not similar to the previous one (anti-grabber). After executing the command, the main unit sends a message about execution to all key fobs with an LCD display programmed into memory. Information about the state of the car is displayed on the display in the form of pictures-icons. More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 7 TOMAHAWK TW-7010 IV. Functions performed using the key fob. Button combination Function x2 x2 2с Note Arming, closing the central locking Ignition off Disarming, opening the central locking Ignition off Closing the central locking Ignition on Opening the central locking Ignition on Disabling the shock sensor Security mode Disabling additional sensor Security mode VALET mode on/off. Not armed mode On/Off sirens. Ignition off Security with the engine running. Ignition on Checking the system status. x2 Search for a car. 2c + + Opening the trunk. 2c Panic. Ignition off 2s Remote Anti-Hijack incl. Ignition on Remote Anti-Hijack off + 2s Immobilizer on/off 2s Automatic arming on/off. - Press x2 at the same time - Press 2 times within a second 2s - Hold until the key fob-pager beeps (or the color of the LED on the additional key fob changes to green) 8 More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 V. How to use the security system. 1. Arming. To turn on the security mode, you must press the button once. . The lights will flash once and the siren will sound once (unless the siren is disabled). The system will close the central locking. The LED will blink evenly. LCD display indication: Attention! If at the moment the security mode is turned on, any trigger is active (for example, a door is open), then the system will give 4 signals with a siren and 4 flashes with side lights. 2. Silent arming At night, you have the opportunity to turn on the security mode without sound notification. In this case, the siren will be disabled. To use this function, press the button. once. The system will close the central locking, the LED will blink evenly, and the lights will flash once. LCD display indication: Attention! The siren sound notification is disabled, but all information is displayed on the key fob display. 3. Disabling the shock sensor and additional sensor. If you leave someone inside a protected vehicle or the vehicle is parked on the side of a busy roadway, it is possible to temporarily disable the shock sensor. To disable the warning zone of the shock sensor after turning on the security mode, press the button 2 times within 1 second. Subsequently pressing this button twice will turn off the main sensor zone. Repeat this procedure to enable the shock sensor. To disable the warning zone of the additional sensor, press the button. 2 times within 1 sec. Pressing it twice again will turn off the main zone of the additional sensor. To enable an additional sensor, repeat this procedure. PASS PASS LCD display indication: or 4. Disabling the security mode. To disable the security mode, press the button. The doors will open, Read more about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 9 TOMAHAWK TW-7010 the siren will sound 2 “CHIRPS”, the side lights will flash 2 times. The polite interior lighting will turn on (optional). LCD display indication: Attention! If, when the security mode is turned off, the siren and key fob with LCD display emit 4 “CHIRPS”, it means that some sensor has been triggered. 5. Two-step disabling the security mode. If the security complex is in alarm mode, i.e. the siren works, the side lights flash, then the first press of the button. returns the system to the “rest” state, and only pressing it again disables the security mode. 6. Security with the engine running. You have the opportunity to activate the security mode with the engine running. To do this you need to: 1) Start the engine. 2) Get out of the car, close the doors, hood, trunk. 3) Press the button. , the door locks will close. 4) Within 3 seconds. After completing step No. 3, press the button. again, the siren will emit 1 “CHIRP” and the side lights will flash 1 time. LCD display indication: Attention! In this mode, the shock sensor and additional sensor are disabled. To disable security with the engine running, press the button. open, the security mode will be disabled. , doors LCD display indication: 7. Automatic arming. This function is turned on and off by holding the button. until the key fob-pager beeps (or the color of the LED on the additional key fob changes to green) and then presses the button. . LCD display indication: Attention! 10 Door locking during automatic arming is programmed (see programming table). More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 8. Automatic re-setting into security mode. This function is programmable. If this function is programmed and you disable the security mode, or this happened accidentally, then within 30 seconds the system will automatically return to the security mode, provided that you did not open the doors or turn on the ignition. 9. Security mode. While in security mode, the alarm monitors all zones and trigger sensors. If triggered, the alarm system is activated. Depending on the security zone, the system has different alarm signals: a) The alarm is caused by the activation of the warning zone of the shock sensor or the warning zone of an additional sensor. The siren will sound 3 CHIRPS and the parking lights will flash 6 times. LCD display indication: b) The alarm is caused by the activation of the main zone of the shock sensor or the main zone of the additional sensor. The siren will work simultaneously with the parking lights for 30 seconds. LCD display indication: c) The alarm is caused by the activation of the main zones: doors, hood, trunk, ignition. The siren will work simultaneously with the parking lights for 30 seconds. The LCD display will display the trigger. 10. Immobilizer mode. This function is activated and deactivated by holding the button. until the key fob pager beeps (or the color of the LED on the additional key fob changes to green) and then presses the button. . If the function is activated, then ~ 30 seconds after the ignition is turned off, it automatically turns on and blocks the engine. The activation of the immobilizer will be indicated by the system LED when the ignition is turned on. LCD display indication: To disable the immobilizer, press the button. turns off, the LED goes out. Attention! , engine blocking Emergency disabling of the immobilizer: 1. Turn off the ignition 2. Press the Override button 1 time. Read more about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 11 TOMAHAWK TW-7010 11. Safe driving function. This function is programmable (see programming table). If the function is activated, the doors are automatically locked after turning on the ignition. (The system has 4 options for setting this function, see page 21, section 2) Attention! If the car doors are opened within 10 seconds after turning on the ignition, this function is automatically disabled. 12. Central locking control while driving. When the car's ignition is turned on, you can control the car's central locking by pressing the button. for closing doors and knobs. to open doors. LCD display indication: - closed - open 13. Search for a car. In the dark, you can use the "Search for Car" function. To do this, press the button. key fob 2 times within 1 second. The parking lights will flash simultaneously with the siren's "CHIRPS" 6 times. Attention! The LCD display will update the vehicle status information. 14. Panic function. You can use this feature to attract the attention of others. With the ignition off, press and hold the button. and, the siren will emit 3 long beeps, the side lights will flash 3 times, the doors will close, the system will turn on the security mode. Attention! The LCD display will update the vehicle status information. 15. Anti-Hijack. To activate this function with the engine running, press the "OVERRIDE" button once; after opening and then closing the door, the function will be activated. The side lights will flash once and the LED will begin to blink. For the operating steps and procedure for disabling the Anti-Hijack mode, see paragraph 16 "Remote Anti-Hijack" LCD display indication: 12 HIJACK More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 16. Remote Anti-Hijack. The function is used to return the car in case of forcible seizure. To activate this function, with the ignition on, press and hold two buttons on the key fob simultaneously. The side lights will flash once and the system LED will start flashing. Remote Anti-Hijack has 3 stages of operation: Stage I: First 30 sec. After activating the Anti-Hijack mode, the system does not manifest itself in any way, the security complex allows the attacker to move somewhat away from you. Attention! At the first stage, it is possible to disable the mode from the key fob; to do this, press the button. or hold down the "OVERRIDE" button for 3 seconds. Stage II: Next 30 sec. The siren emits warning "CHIRPS" and the parking lights flash. Stage III: The final stage occurs after approximately 60 seconds. after activating the Anti-Hijack mode. The siren will sound and the engine will be locked. Attention! To disable the Anti-Hijack mode at stages II and III: 1. Turn on the ignition. 2. Press and hold the button. OVERRIDE for 3 seconds. (the siren will emit 3 “CHIRPS”) 3. Turn off the ignition. 4. Anti-hijack mode will be disabled. The system will remain in armed mode. If a PIN code is programmed, disabling the “Anti-hijack” mode can only be done by entering the PIN code. LCD display indication: HIJACK 17. Valet mode. Valet mode is used by the car owner if the car is transferred to third parties, for example, for maintenance. After activating this mode, the system can only perform service functions such as controlling an additional channel or central locking. Valet mode is turned on and off when security is turned off by holding the button. until the key fob pager beeps (or the color of the LED on the additional key fob changes to green) and then presses the button. , or by holding the book. "OVERRIDE" for 3 seconds, with the ignition on. The activation of the Valet mode will be confirmed More about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 13 TOMAHAWK TW-7010 by 4 flashes of parking lights and 4 “CHIRPS” of the siren, the LED will be constantly on. LCD display indication: 1-1 Z Z Z 18.Protection against false alarms. The Tomahawk TW-7010 security system is a highly intelligent car security device, so the system uses a complex, multi-level algorithm for protecting against false alarms. First level. When the security mode is turned on, the main unit tests all security zones; if any sensor is found to be defective, the system automatically turns it off and notifies you about this using 4 “CHIRPS” of the siren. LCD display indication: icon of the corresponding trigger. Second level. During the security mode, the system analyzes the operation of the sensors; if the shock sensor or additional sensor is triggered 8 times in a row, it will be disabled. 19. Remote polling of the status To perform a remote polling of the vehicle’s status, press the button. The parking lights will flash 3 times, the key fob pager will display the vehicle’s status. Attention. If after pressing the button. (or any other button) within 3 seconds there is no confirmation of the command execution and the key fob pager emits 1 “Beep”, which means the vehicle is outside the range of the key fob pager transmitter. 20. Remote trunk release (additional channel). To implement this function on many vehicles, additional equipment must be installed. If this option is enabled, then to unlock the trunk you must press and hold the button. key fob until the key fob pager beeps (or the color of the LED on the additional key fob changes to green) and then presses the button. . Execution of the command will be accompanied by 3 flashes of parking lights and “CHIRPS” of the siren. Attention 14 If the system was armed when the trunk was unlocked, the shock sensor and trunk trigger will be disabled until the trunk is closed. More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 LCD display indication: 21. Remote siren shutdown. In many countries, the use of car alarm sirens at night is prohibited (for example, in Moscow after 2300), so the security system provides for turning off the siren from the key fob. To do this, the system must be in security mode, then press the button. . LCD display indication: In this case, the system will be fully operational, with the exception of the sound warning from the siren. All information will be displayed on the LCD display of the key fob. The siren is turned on by pressing the button once. LCD display indication: 22. Additional channel control. The additional channel makes it possible to use the car’s standard devices, open the trunk, control the power windows, turn on the path illumination at night with the car’s headlights, etc. To control an additional channel, you must press and hold the key fob button until the key fob pager sounds a sound (or the color of the LED on the additional key fob changes to green) and then press the button. , the parking lights will flash 2 times to confirm the command has been completed. Additional activation time channel is programmed (see programming table). Attention! The LCD display will update the system status information. 23. Emergency arming/disarming. If your key fob does not function or is lost, you have the opportunity to enable or disable the security mode using the OVERRIDE button. To do this: 1. Emergency arming: 1) Open the door and turn on the ignition. 2) Press the button. OVERRIDE 3 times. 3) Turn off the ignition (the siren will emit 1 “CHIRP”, the parking lights will flash 1 time). 4) 20 seconds later the system will turn on the security mode without locking the doors. Attention! If you have used emergency arming, the system will enable a 20-second delay in the alarm mode when triggered, thereby giving you the opportunity to use Read more about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 15 TOMAHAWK TW-7010 emergency disarming without turning on the alarm mode. 2. Emergency disarming: 1) Open the door and turn on the ignition. 2) Press the button. OVERRIDE 3 times. 3) Turn off the ignition (the siren will emit 2 “CHIRPS”, the side lights will flash 2 times). 4) Security mode will be disabled immediately. Attention! If you have programmed a personal PIN code, then emergency disarming is performed only using this PIN code. 24. Personal code (PIN code). This code (if programmed) allows the owner to disable the security mode without a key fob, as well as disable the Anti-Hijack mode at stages II and III. The PIN code consists of two digits. Attention! Factory setting of the PIN code is 1:1 1st digit 1(x) 2nd digit 1(y) Disabling the security mode using a PIN code. If your key fob does not function, or the system is at stage II or III of the Anti-Hijack mode, then you can disable the security mode using the PIN code. To do this: 1. Open the door and turn on the ignition. 2. Press the "OVERRIDE" button a number of times equal to X (the first digit of the PIN code). 3. Turn off the ignition. 4. Turn the ignition back on. 5. Press the "OVERRIDE" button a number of times equal to Y (the second digit of the PIN code). 6. Turn off the ignition. If the PIN code value is entered correctly, the security mode will be disabled. Attention! Repeat the procedure if you fail to enter the PIN code. 25. Programming a new PIN code. Attention! 16 Programming a new PIN code is possible only if “Emergency shutdown of the system using Read more about the TOMAHAWK TW-7010 car alarm system on the website http://intorg.ru TOMAHAWK TW-7010 PIN code” is programmed (see “Programming Table”) To change the PIN code necessary: ​​1. Turn off the ignition. 2.Press the "OVERRIDE" button 4 times. 3. Turn on the ignition, the siren will emit 4 “CHIRPS”. 4.Press the "OVERRIDE" button once to turn on the PIN code programming mode. 5.Using the existing key fob, enter the new value of the first digit of the PIN code. Meaning of the number Attention! Corresponding button 1 Press button 2 Press button 3 Press button 4 Press the button The siren will confirm the new value of the 1st digit of the PIN code with the number of “CHIRPS”. 6. Press the OVERRIDE button 1 time to enable programming mode for the 2nd digit of the PIN code. 7. Using a valid key fob, enter a new value for the second digit of the PIN code. Meaning of the digit Corresponding button 1 Press button 2 Press button 3 Press button 4 Press button Attention! The siren will confirm the new value of the 2nd digit of the PIN code with the number of “CHIRPS”. Attention! We recommend writing down the new PIN code value. More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 17 TOMAHAWK TW-7010 26. Programming new key fobs. Up to 4 key fobs can be stored in the memory of the main unit; for this you need to: 1. Turn off the ignition. 2. Press the OVERRIDE button 7 times. 3. Turn on the ignition. The siren will emit 7 “CHIRPS” confirming entry into the key fob programming mode. 4. Press and hold the buttons and the new key fob simultaneously for 1 second. The "CHIRPS" system will confirm the entry of a new key fob into memory (1 "CHIRPS" for the first, 2 "CHIRPS" for the second, 3 "CHIRPS" for the third and 4 "CHIRPS" for the fourth). After that, perform this operation with the next key fob (if necessary). Attention! All lost key fobs will be erased from the system memory, so the programming procedure must be performed on all key fobs that you intend to use in the future. Attention! If no actions were taken to program the key fobs within 6 seconds, the programming mode will automatically turn off. 27. Information about programmed key fobs. For security purposes, the Tomahawk TW-7010 security complex has introduced the function of viewing the number of programmed key fobs. To display this information: 1. Turn the ignition on. 2. Press the button. keychain 3. The number of LED flashes will indicate the number of key fobs already programmed into the system. 28. Information about the performance of sensors. To check the functionality of the sensors, turn on the ignition and activate the sensor whose functionality you want to check (for example, open the door). If the sensor is working properly, the system LED will begin to blink slowly and go out when the door is closed, indicating that the sensor is working. 29. Display information on the LCD key fob. This security complex is equipped with a new warning system, so information about the execution of a command or a change in the system status will be displayed on the LCD displays of all key fobs programmed into the system memory that are within the system’s coverage area. 18 More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 30. Functionality of the key fob pager. Buttons used Functions performed F Turning on the backlight F + F Turning on the locking of the key fob-pager buttons + F Turning off the locking of the key fob-pager buttons hold Notes Automatically turns off after 2 seconds Indication: Clock, alarm, timer setting mode Clock setting mode - clock F 1 time Setting mode hours - minutes F 2 times Alarm setting mode - hours F 3 times Alarm setting mode - minutes F 4 times Alarm setting mode - on/off F 5 times Timer setting mode - hours F 6 times Timer setting mode - minutes F 7 times Setting mode timer - on/off - forward forward - backward forward - on. - off - forward translation - backward translation - on. Read more about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru - off. 19 TOMAHAWK TW-7010 31. LED indication. The system LED is multifunctional. Using LED signals, you can determine the current state of the security system from the table: Mode Security mode Immobilizer mode VALET mode 1st and 2nd stages Anti-Hijack Ignition off Ignition on * * * * * * * * * * * Constantly lit Constantly lit * * * * * * * * * * * 32. Procedure for replacing the battery in the key fob with a display. LCD key fob with LCD display has a battery charge level indicator (type AAA, 1.5V). If the indicator shows a low charge level, then it is necessary to urgently replace the battery. To replace the battery: 1. Open the protective cover on the back of the key fob. 2. Take out the old battery. 3. Press the key fob button. 4. Install a new battery, observing the polarity (type AAA, 1.5V). 5. Close the protective cover. 6. Press the key fob button, the display will show the system status. 33. Function programming mode. To enter programming mode, perform the following steps: 1. Turn off the ignition. 2. Press the “OVERRIDE” button 5 times. 3. Turn on the ignition (confirmation of entry into the programming mode - 5 “CHIRPS” of the siren). Use the “OVERRIDE” button to select the desired function. Each press - transition to the next function The system will indicate the selected function with the “CHIRPS” of the siren: Short “CHIRP” - 1 Long “CHIRP” - 5 EXAMPLE: 7 presses of the “OVERRIDE” button - 1 long “CHIRP” and 2 short ones - 20 selected More details car alarm TOMAHAWK TW-7010 on the website http://intorg.ru TOMAHAWK TW-7010 function 7. See the programming table for numbers and descriptions of functions. 34. Return to factory settings. To return to factory settings of programmable functions: 1. Turn off the ignition. 2. Press the “OVERRIDE” button 10 times. 3. Turn on the ignition (confirmation -10 “CHIRPS” of the siren). 4. Press the “OVERRIDE” button 1 time (confirmation 1 “CHIRP” siren). 5. Press the button. keychain More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 21 22 Polite lighting or closing the windows (blue wire) Automatic re-arming Siren or horn Pulse duration of the additional channel (sec.) Engine blocking type 6 times 7 times 8 times 9 times 10 times Note. Factory settings in the table are underlined. Emergency shutdown of the system using a PIN code 5 times NC 0.8 Siren On. Courteous Backlight Off Off 3 times Locking doors during automatic arming Var. 1 Accounting for interior lighting delay or arming delay 4 times On. Safe driving function 2 times Open: 0.8 Close: 0.8 Button Pulse length for opening/closing central locking (sec.) Function 1 time Number of button presses. OVERRIDE HP 10 Var. 2 Off Courteous Backlight On On Var. 2 Var. 2 Open: 3.6 Close: 3.6 Button VI. HP 30 Programming Table Horn Off Window closing On On Var. 3 Var. 3 Open: 2 x 0.8 Closed: 0.8 HP button On/Off. Klaxon Off Window closing On On Var. 4 Off Var. 4 TOMAHAWK TW-7010 button Read more about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 Description of the programmable functions of the system. 1. Length of the central locking activation pulse: 1) Closing pulse - 0.8 seconds, opening pulse - 0.8 seconds 2) Closing pulse - 3.6 seconds, opening pulse - 3.6 seconds 3) Closing pulse - 0 .8 sec., opening impulse - double 0.8 sec. 4) Closing impulse - 30 seconds, opening impulse - 0.8 seconds. 2. Safe driving function: 1) The doors close when the ignition is turned on, open when the ignition is turned off 2) The doors close after 10 seconds. after the ignition is turned on, open when the ignition is turned off 3) The doors do not close when the ignition is turned on, they open when the ignition is turned off 4) The doors do not close when the ignition is turned on, and do not open when the ignition is turned off 3. Taking into account the interior lighting delay or arming delay: 1) Taking into account the interior lighting delay lighting is on 2) Interior lighting delay accounting is turned off 3) Arming delay is 30 sec. 4) Arming delay 45 seconds. 4. Locking doors during automatic arming: 1) Doors do not close 2) Doors close 3) Doors close 4) Doors close 5. Emergency system shutdown using a PIN code: 1) Emergency system shutdown without a PIN code 2) Emergency disabling the system only using a PIN code 3) Emergency disabling the system using only a PIN code 4) Emergency disabling the system using only a PIN code 6. Courteous lighting or closing windows (blue wire): 1) Polite lighting. Pulse duration 20 sec. appears when disarming 2) Polite backlight. Pulse duration 30 sec. appears when disarming 3) Closing the windows. Pulse duration 20 sec. appears when arming Read more about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 23 TOMAHAWK TW-7010 4) Closing the windows. A 30-second pulse appears when arming 7. Auto-re-arming: 1) Auto-re-arming on 2) Auto-re-arming off 3) Auto-re-arming off 4) Auto-re-arming off 8. Siren or horn: 1) Siren 2) Siren on. when arming, off. when disarming 3) Klaxon 4) Klaxon 9. Pulse duration of additional channel (sec.) 1) 0.8 2) 10 3) 30 4) On/off. 10. Engine blocking type: 1) Normally closed 2) Normally open 3) Normally open 4) Normally open 24 More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 Installation Guide. I. Basic principles of installation. The Tomahawk TW-7010 security system has a classic connection diagram. First of all, before starting the installation, turn off the on-board power supply to the vehicle (disconnect the “-” battery terminal). To select installation locations for security system units, be guided by the following principles: - Concealment of installation. -Absence of sources of heat and moisture release near the blocks. -Provide for minimal influence of standard electronics and alarm units on each other. Attention! The radiating antenna must be installed away from the alarm and vehicle control units. When installing, try to minimize the length of the wires. II. Selecting the location of the main units 1. The electronic alarm control unit is installed inside the vehicle. To obtain maximum range, the transmitting-receiving “RF” antenna of the system unit must be positioned as high as possible and not come into contact with metal objects or electrical wiring harnesses. 2. The siren is installed in the engine compartment, in an inaccessible place; if you are using an autonomous siren, provide access to the service key hole. The siren should be installed with the horn facing down, this will prevent moisture from entering. It is better to plan the wire connections inside the cabin for less oxidation. 3. All high current circuits (power supply, parking lights, central locking, etc.) must be protected by fuses of the appropriate rating. 4. The hood and trunk triggers cut into places protected from moisture that are inaccessible when the hood and trunk are closed. Triggers need to be lubricated periodically to prevent seizing and corrosion. 5. The shock sensor is installed in the passenger compartment, the center of the car can be considered ideal, it is attached to the metal of the body with self-tapping screws or glued. 6. Additional sensors are installed in locations that provide the best performance. 7. Contacts in places where ignition, starter, etc. circuits are broken. It is recommended to solder. Read more about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 25 TOMAHAWK TW-7010 III. Connecting the system. Main connector 14 PIN. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Red wire - system power (connect to the “+” terminal of the battery through a 15A fuse). Green-black wire - output of the “+” contacts of the side light relay (connection via a 7.5A fuse). Black wire - power supply to the “-” system (ensure strong, reliable contact). Green-yellow wire - output of the “+” contacts of the side light relay (connect through a 7.5A fuse). Blue wire - output "-" control of courtesy lighting or control of power windows (300mA max). The yellow wire is the “+” input from the ignition switch. Black and yellow wire - output "-" control on the blocking relay (output is programmable, 300mA max). Gray wire - output "+" control of a siren or standard horn (1.5A max, programmable). The orange-violet wire is the handbrake wire. Connection to the "-" handbrake switch with a manual transmission or to the brake lights with an automatic transmission. Yellow-black wire - output "-" of the additional channel, appears when activated from the key fob (300mA max, programmable). The blue-red wire is the “+” input of the door triggers. The blue-black wire is the “-” input of the door triggers. The orange-white wire is the “-” input of the trunk trigger. The orange-gray wire is the “-” input of the hood trigger. 6 PIN connector. (built-in central locking relays) 1. 2. 3. 4. 5. 6. 26 Blue wire - central contact of the central locking unlocking relay. The green wire is the central contact of the central locking relay. The black-red wire is the normally open contact of the central locking unlocking relay. The black and red wire is the normally open contact of the central locking relay. The blue-black wire is a normally closed contact of the central locking unlocking relay. The green-black wire is a normally closed contact of the central locking relay. More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 Shock sensor connector 4 PIN. 1. 2. 3. 4. Sensor power supply "+12V". Sensor power supply "-". Input "-" warning zone. Input "-" of the main zone. Additional sensor connector 4 PIN. 1. 2. 3. 4. Sensor power supply "+12V". Sensor power supply "-". Input "-" warning zone. Input "-" of the main zone. OVERRIDE 2 PIN button connector. Connector 2 PIN - connector for connecting the OVERRIDE button. 2 PIN LED connector. Connector 2 PIN - connector for connecting an LED. 4 PIN transceiver antenna connector. 4 PIN connector - connector for connecting an antenna. Connector for connecting GSM/GPS module 3 PIN. 3 PIN connector - for connecting a GSM/GPS module. Read more about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 27 TOMAHAWK TW-7010 IV. Connection diagrams Connector 3 PIN not used Connector for additional sensor 4 PIN ® TOMAHAWK Connector for GSM/GPS module 3 PIN Connector for transceiver antenna 4 PIN LED connector 2 PIN Connector for “OVERRIDE” button 2 PIN Connector for shock sensor 4 PIN Main connector 14 PIN Fig. 4 28 Central locking connector 6 PIN More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 Blue 10A Green 10A UNLOCK COM LOCK COM Black-red UNLOCK NO LOCK NO Blue-black UNLOCK NC Green- black LOCK NC 15A Red 7.5A Green-black Black +12V from battery For side lights; “+” 7.5A Green-yellow Blue Yellow Black-yellow output “-” To side lights; “+” Interior lighting or raising windows; “-” 300mA Input from the ignition switch “+” Engine blocking 300mA max Gray output “+” 1.5A max Orange-violet Yellow-black Handbrake sensor; "-" Add. channel; output “-” 300mA Blue-red input “+” of door sensors Blue-black input “-” of door sensors Doors +12V Doors Orange-white input “-” of trunk sensor Trunk Orange-gray input “-” of hood sensor Hood Shock sensor Button “Override” LED Transceiver antenna Connector for connecting a GSM/GPS module Connector not used Connector for connecting an additional sensor Diagram 1 More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 29 TOMAHAWK TW-7010 Connecting an additional electric drive Control time. 0.8 sec. 87A NC Blue-black 30 COM Blue NO Black-red NC Green-black 30 COM Green NO Black-red 87 87A 87 Pr 15A +12V Scheme 2 Positive central locking control. Exercise time 0.8 sec. 87A NC Blue-black 30 COM Blue NO Black-red NC Green-black 30 COM Green NO Black-red Central locking unit Opening 87 87A Closing 87 Pr 1 - 3A +12V Scheme 3 30 More information about the TOMAHAWK TW-7010 car alarm on the website http ://intorg.ru TOMAHAWK TW-7010 Negative control C.Z. Exercise time 0.8 sec. 87A NC Blue-black 30 COM Blue NO Black-red NC Green-black 30 COM Green NO Black-red Central locking unit Opening 87 87A Closing 87 Pr 1 - 3A -12V Scheme 4 More information about the TOMAHAWK TW-7010 car alarm on the website http: //intorg.ru 31 TOMAHAWK TW-7010 Connecting polite lighting. If your car does not have a courtesy light function, then using the Tamahawk TW-7010 it is possible to connect this service function. Blue wire 86 87 +12V 85 87a Standard courtesy lighting unit 30 Scheme No. 5 Organization of courtesy lighting. Option 1 Blue wire 86 87 +12V 85 30 86 87 +12V +12V +12V Option 2 Blue wire 87a 85 87a 30 Scheme No. 6 32 More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 Engine blocking connection. The Tomahawk TW-7010 security system has a programmable blocking relay control output, which allows you to get a normally open blocking option from a normally closed starter blocking; therefore, the connection diagram also changes. Engine blocking. Option 1 Normally closed interlock. Black wire with a yellow stripe 86 87 Yellow wire 85 87a 30 Locking relay Fuel pump, switch, ignition coil, starter, etc. Option 2 Normally open interlock. Black wire with a yellow stripe 86 87 Yellow wire 85 87a 30 Locking relay Fuel pump, switch, ignition coil, starter, etc. Diagram No. 7 Read more about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 33 TOMAHAWK TW-7010 Connecting a standard horn. Tomahawk TW-7010 allows the connection of both a regular siren and a standard horn; the option of using an audible warning device is selected by software (see programming table). If you decide to use a standard horn, the connection system is shown below. Connecting the standard horn. To the standard horn button Gray wire 86 87 85 87a 30 Standard horn +12V Diagram No. 8 Attention! 34 Be sure to use a socket with a protection diode. More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru TOMAHAWK TW-7010 V. Technical data. Nominal voltage +12V Current consumption when switched off. ignition 16mA Operating frequency 434 MHz Modulation type FM (frequency) Range*: from key fob-pager to alarm from alarm to key fob-pager up to 1200 m up to 1200 m *- Range is indicated provided there is no interference. It is influenced by many factors, such as buildings, trees, power lines, the relative position of the car and the pager key fob, weather conditions and much more. Allowable current: Power circuit red wire (limited by a fuse) 15A Circuit of contacts of the central locking control relay (limited by a fuse) 15A Contacts of an external blocking relay 30A Siren power output “+” (gray wire) 1.5A Additional channel output “-” (programmable, yellow -black wire) 300mA Power output for parking lights “+” (green-black wire, green-yellow wire) 7.5A Control output for courtesy lighting or power windows “-” (programmable, blue wire) Control output for locking relay “-” (Programmable, black-yellow wire) 300mA 300mA More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru 35 TOMAHAWK TW-7010 Time delays: Additional channel output "-" (yellow-black wire) Programmable: 0.8 sec. 10 sec 30 sec On/off Duration of central locking control Programmable: 0.8 sec 3.6 sec 30 sec Siren/horn output (gray wire) Programmable VI Equipment Central module Key fob with LCD display . Keychain standard type. Shock sensor. Light-emitting diode. Antenna. Harnesses for connecting the central unit, central locking, antenna. Push-button type limit switch. Instructions. Packing box. ME-83 The device meets the climatic requirements in accordance with GOST 15150, version UHL2 (placed inside an enclosed cabin). The device complies with the electromagnetic compatibility requirements of GOST R 50789-95. 36 More information about the TOMAHAWK TW-7010 car alarm on the website http://intorg.ru