How to make a wipe from a finger battery. Homemade vapes. Electronic cigarette from a cartridge case

The popularity of electronic cigarettes is growing every year. Manufacturers claim that these devices help you quit smoking completely. But not all smokers can afford to buy this fashionable device, so some of them try to make an electronic device with their own hands. This process does not seem too complicated at first glance, but it requires certain knowledge and skills. You can make a vape at home using a pen or an unnecessary flashlight.

Process Features

Making a vape at home without any knowledge of electronics and mechanics is almost impossible. This process requires special attention, accuracy and perseverance.

It is worth paying attention to the quality of the materials and components used.

A homemade electronic cigarette is unlikely to have a beautiful and stylish appearance, but in terms of their design, vapes made at home are not much different from store-bought devices. You can also make your own liquid for an electronic device.

Assembly instructions

There are several ways to easily make a vape at home yourself, using various available materials:

handle;
paper;
syringe;
flashlight, etc.

The simplest option is a battery-powered device without a battery or other accessories.

For this you will need:

insulating tape;
cardboard;
pliers;
clamp;
the wire;
scissors;
4 "long-lasting" batteries;
cartridge.

In order to do electronic cigarette yourself, you need:

1. Assemble the batteries “plus” to “minus” so that the “plus” of the last battery is located at the top.
2. Cut a piece of wire 3 cm longer than the length of the folded batteries.
3. Remove the insulation from the wire by 5 cm on one side and 2.5 cm on the other. Where the wire is exposed more, it is necessary to make a spiral.
4. Install the clamp to the opposite end of the wire and crimp with pliers.
5. Connect the spiral end to the negative of the upper battery.
6. Secure the structure with insulating tape.

1. Draw and mark the length of the batteries, then bend a loop at the bottom of the wire and attach it to the bend with glue. Upper part Wrap the resulting tube with an elastic band.
2. Place the batteries in the tube so that the negative wire is directed downward from the bent end.
3. The wire must be secured so that the “extra” piece of it sticks out of the cardboard tube.
4. Secure the clip with an elastic band.

The remaining batteries are installed in the same way.

The finished cartridge can be purchased at any vaping store. Some of them already have connectors.

The next step is to cut a piece of metal into a "T" shape, then bend the device around an insulated screw.

To power the electronic cigarette, you need to attach the clamp to the ring base of the cartridge, then connect the central terminal with the “plus” of the batteries.

Knowing the structure of an electronic cigarette and more or less understanding the technology, you can even assemble... a homemade vape. Why is this necessary? Firstly, the device can be made from cheap materials, saving money. Secondly, creating something with your own hands is always more interesting than buying it.

For or against

To decide whether to make a homemade vape, you need to carefully weigh all the pros and cons. If we talk about the advantages of home-made, then such a device will be:

By making a vape yourself, the master takes full responsibility for its quality, capabilities and safety. However, the slightest error in assembly can lead to an explosion or fire of the device. But no one will have this. And knowing all the “stuffing” from the inside, the owner of an exclusive can easily repair it.

Under no circumstances should you start making a device if you do not have experience in such matters and do not understand electronics!

Manufacturing

Before you learn how to make a vape with your own hands, you need to have an idea about the structure of an electronic cigarette. In principle, the manufacture of this device involves the construction of a box mod (battery) and an atomizer (evaporator).

It's not that difficult to make a mechanical box mod. This is a device that supplies voltage from the battery to the atomizer when you press a button. Everything you need to create it can be bought at a radio store or ordered online. You will need:

14 AWG Copper wire;
connector 510;
mosfet;
button;
battery compartment.

Well, and, strictly speaking, the battery itself is a high-current 18650 format, from 20 amperes and above. Sony and Samsung have similar ones. This is the most expensive part of the device.

A considerable amount of the cost of an electronic device is consumed by the cost of its housing. A homemade product can be made from inexpensive materials - plastic, metal, or at least thick cardboard. You can show your imagination and make, for example, a wooden case, decorating it with carvings. This box must have holes for gas venting.

The atomizer is inexpensive, so it’s easier to buy a ready-made one and attach it to a homemade mod.

However, many craftsmen bother making not only atomizers, but also assembling a battery from batteries connected by wire.

Vaper's ABCs

IN modern world Smoking has become a real scourge of society. But fortunately, people have the opportunity to get rid of this bad habit without exposing your body to “torment.”

Electronic cigarettes are not only a great option to give up regular cigarettes. tobacco products, but also the opportunity to follow fashion. However, the cost of modern gadgets limits their use, because not everyone has money for branded devices. There is a way out of this situation - make a vape yourself.

Most vapers are confident that the vaping device they purchase is much cheaper than a regular purchase. regular cigarettes. But, given the huge markups of companies that sell such products, this is absolutely not the case. Therefore, many vapers prefer to make their own vape.

Of course, any vaper can go to a store or order any gadget they like on the Internet. However, experienced vapers believe that only a self-assembled device emphasizes their experience in this culture.

You can build such a neat box yourself.

Knowing how basic windings are implemented (types of spirals were discussed earlier) and what an electronic cigarette consists of, you can use it correctly and practically.

With the necessary knowledge on how to assemble a vaping device, this process does not seem so difficult. But at the same time, the person who will assemble the electronic cigarette must have some experience in such activities.

In this matter, it is extremely important to carefully select materials, as well as use the appropriate tools that will be suitable for creating a homemade vape. If you assemble the vaping device incorrectly, then during its operation you can get burns to the face, lungs, and respiratory tract.

Using the same principle, it will not be possible to create a liquid without proper knowledge in the field of chemistry. Therefore, if you do not have experience in this area, then it is better to use a purchased, high-quality vaping liquid. However, there are also craftsmen who, having the necessary reagents and aroma oils, create unique and pleasant mixtures for vaping.

If the vaper does not have proper experience in such matters, then it is better to abandon the idea self-made vaping devices.

Cardboard vape? Are you seriously?

If you decide to assemble an electronic cigarette on your own, you can try making vaping devices from a cardboard tube.

Selection of battery and wire

Experts advise giving your preference to either the 3 Ds or the 4 Cs. Both options are great for DIY electronic cigarette assembly. It all depends on individual preferences and ease of use.

Having decided on the choice of battery, you need to connect and assemble them into a serial chain using electric wire. The length of the latter should be approximately 30 mm longer total length folded batteries.

Wire preparation

At this stage, it is necessary to remove the insulating coating from the wire using pliers.

If the wire is twisted, you need to straighten it with your hands.

Making a contact spiral

The production of a spiral is carried out using bare wires.

In this case, the clamp must be installed at the opposite end of the wire, while the wire itself is crimped with pliers.

Spiral connection

The spiral-twisted end is connected to the negatives of the battery and secured with electrical tape.

Case manufacturing

Electrical diagram of the cartomizer.

Due to the fact that our sample vaping device is budget-friendly, all the savings come from the body part of the device. It is made from a cardboard tube cut along the entire length.

Installing the battery into the body of the device

At this stage, you need to install the first battery into the resulting device, but this is done in such a way that the minus point faces the bent end.

The wiring is installed in such a way that the clamp on top of the cardboard case protrudes slightly. All other batteries (and there are only 3 of them) are installed according to the same principle.

Cartridge re-twisting

The most difficult part in completing the task will be creating the plugs through which the cartridge will be installed. In most cases, V2 cartridges are already equipped with a special connector. All that remains is to come up with something with the plug.

To do this, take a screw and simply wrap it with electrical tape. Having cut out the letter “T” from ordinary metal, we bend it around our “plug”.

Assembling a homemade cigarette

To finally prepare the device for vaping, you need to attach the clamp to the outer rings of the output of the installed cartridges. The E-cigarette is activated by connecting the central terminal in the cartridge and the plus of the battery from the very top.

If the cigarette is not used, then it is necessary to ensure that these contacts do not touch each other. Otherwise, the fibers that are inside the device may overheat, which will lead to quite disastrous consequences.

In addition, it is necessary to protect the homemade vaping device from short circuits. By following these tips, your homemade electronic cigarette will last a long time, and the vaper himself will be able to save money.

Electronics from a sleeve

Another option on how to make an electronic cigarette:

Now you know how to make an electronic cigarette with your own hands. We hope these tips will help you create your own unique vape. Good luck!

Today, vaping culture is becoming increasingly popular. Among the variety of devices for vaping, it is extremely difficult to give preference to any of them: these are small eGoshkas, multifunctional box mods, simple electronic cigarettes, mechanical mods, etc.

But at the same time, many vapers, both beginners and more experienced, practice making vape with their own hands. Firstly, it is cost-effective, and secondly, you can make your own exclusive vaping device. You will learn how to make a vape from this publication.

Homemade vape (electronic cigarette) is a real innovation among modern youth. Manufacture homemade vape not easy. You need to use your brain a little and understand electronics or mechanics.

Of course, you shouldn’t count on getting a luxurious, high-quality electronic cigarette. For a moment, the electronics sold are developed by qualified engineers and designers. But at the same time, the implementation of such designs will bring a lot of pleasure to the vaper and will amuse his excitement.

In addition, a homemade mod will be able to provide vaping on the same principle as a purchased device. Moreover, originality will in no way affect the quality of soaring.

So, how to assemble a homemade vape on your own?

Step-by-step instructions for making an e-cigarette

The procedure for creating an electronic cigarette cannot be called complicated, but at the same time it requires from the master some knowledge, skills, patience, painstakingness and perseverance.

In this publication, we offer you basic tips that will help even novice vapers assemble a full-fledged electronic cigarette. Of course, we will not talk about how to turn electronics on a lathe.

We have selected for you the most primitive method of making a battery-powered vaping device, without a power supply, batteries or other accessories.

Of course, you won’t be able to assemble a homemade vape without even having a primitive kit for this. Therefore, first of all, you need to stock up on basic materials. To ensure that your e-cigarette is of the highest quality, give preference to “internals” that are of appropriate quality.

All necessary materials and tools can be obtained at home by digging in deposits with all sorts of things.

Well, for those who do not store such spare parts in their pantry or in a box with all sorts of necessities, you can purchase them at specialty store. For example, electronic cartridges (regardless of whether it is a homemade mod or a purchased one) are purchased in the traditional form.

What is needed to create an e-cigarette?

To assemble a homemade vape you will need the following materials and tools:

scissors;
batteries - 4 pieces (if possible, it is better to take C or D, preferably good quality, for example, Duracell);
insulating tape;
a cardboard tube that will act as a housing for the electronics;
pliers;
screw;
glue or stapler;
crocodile clip;
the wire;
e-liquid cartridge.

Don’t skimp on consumables, because this will help you create a better and truly worthy electronic cigarette.

Manufacturing algorithm

The entire process of creating an e-cigarette consists of sequentially performing the following manipulations:

We take 3 “D” batteries (or 4 “C”) and collect them in a certain sequence, plus and minus. The main thing is that the plus of the outermost battery is on top.
Next you need to take a small piece of electronic wire (its length should be approximately 3 cm longer than the length of the folded batteries). We disconnect the wire with pliers, while removing the insulation from the edges. If the wiring is twisted (twisted), then it must be unbent manually.
We expose the wire: on one side, by 5-7 cm, and on the other, by 2.5 cm. The edge where the wire is exposed the most must be bent in the form of a spiral. The “crocodile” is installed on the opposite side, and the resulting part is crimped with pliers. We attach the edge on which the spiral is made to the “-” pole of the upper battery and secure it with electrical tape.
We will make the body from cardboard and the stronger it is, the better. You can use a ready-made cardboard tube: it is cut and fixed to a certain diametrical size (so that the batteries fit into it freely).
We mark the length of the batteries, then bend the loop at the bottom of the wire and firmly attach it to the bend using glue or a staple. It is advisable to wrap the upper part of the future e-cigarette case with an elastic band.
Next, we place the batteries in the tube so that the minus wire, which is located on the batteries, is directed downwards from the bent end. After this, we fasten the wire in such a way that the “extra” piece protrudes from the tube. The clip is secured with an elastic band. The remaining batteries are installed according to a similar principle.
We form a plug for the cartridge. To do this, take a regular screw and wrap it with electrical tape (this piece will become the central terminal). We cut out the letter “T” from a loose metal plate and bend it around the fixed screw.
For the vape to start working, you just need to attach the clamp to the ring base of the cartridge.

The operation of electronic cigarettes or vape is based on the principle of vaping, where a special liquid is used as a refill. Vaping mixtures are presented in stores in a large assortment, but they are often highly priced and do not always meet taste preferences steamer By experimenting with ingredients at home, you can create your own mixture that perfectly matches the characteristics.

Show all

Rules for preparing the filling

Before you start making e-liquid, you need to determine which properties are important for the final product: smoke, throat hit, nicotine content or taste and aroma. Depending on this, a formula is selected, increasing or decreasing the amount of a particular substance. There are variations of classic proportions, but with some experience and knowledge, you can derive a ratio that is ideal in all respects.

Vapor from vaping and electronic cigarettes, entering the body, acts directly on the mucous membranes. That is why, when producing liquid, it is necessary to comply with safety precautions and certain rules.

It is necessary to use only those components whose quality is confirmed by certificates. They should only be purchased in pharmacies and special, trusted stores, where, if problems arise, you can file a complaint about the quality of the product.
Note about high degree cleaning is required for containers with nicotine and propylene glycol.
You should not start with large volumes, since each person has individual perception characteristics. It makes sense to try several variations of the mixture in small quantities. If the liquid is cooked in large quantities, it may not be to your taste and the ingredients will be wasted.
If the mixture will be stored for a long time, it is best to place it in the refrigerator.

Main components of the liquid

Making your own liquid for electronic cigarettes and vaping is based on maintaining the proportions of ingredients and additives that help improve the quality of taste or smoke. For creating perfect formula it is necessary to know what properties a particular component of the mixture has.

To get a mixture similar to a store-bought one, you need to use a number of main components, trying not to greatly change their proportions in the composition. The main substances that make up the vaping liquid include:

1. Propylene glycol is a liquid food additive that is viscous and has a sweet taste that can enhance the taste of flavorings. It binds the components of the liquid and quickly penetrates the mucous membranes, that is, it is responsible for the delivery of nicotine and flavoring substances to the receptors. A liquid in which the percentage of this additive exceeds the other components is distinguished by high strength, it is heavy and saturated, and produces a small amount of steam.
2. Glycerin is a transparent, viscous liquid, which is also used to bind other substances. It increases the amount of steam produced by the device and softens the taste of the final product. Liquid made from glycerin is lighter and sweeter. The ingredient can be purchased at the pharmacy, but the water content in the substance should not exceed 20%, otherwise the batch will turn out to be too liquid.
3. Distilled water - used as a solvent for the remaining components. Due to the absence of salts and gases in its composition, it does not distort taste qualities additives and dilutes the final product to the desired state. Without adding water, a burning and burning taste may occur due to poor wetting of the wick.
4. By adding nicotine to a self-mix, you can vary it in degree of saturation, making both “zero” liquids free from it and full-fledged substitutes strong cigarettes. For vaping, it is used in the form of an oily liquid with pungent odor, which easily dissolves in water. The dosage of this substance should be approached with special care, since pure form nicotine is a potent poison.

To create e-liquid, you should choose not a natural, but a synthetic substance of well-known brands: “Johnson” - has practically no taste and has a moderate strength, “Merck” - has a taste of molasses or burnt sugar, Chinese nicotine produced in Shanghai has a pronounced aroma of ash, tobacco or cigars. When preparing a dressing with flavors, it is better to choose Johnson, since the flavors are perfectly revealed on its basis, without being burdened by additional notes. The other two options are also suitable for independent smoking, since their aroma is quite capable of replacing a classic cigarette.

Synthetic substances produced by other brands do not have a consistent composition. Therefore, when using them, you can get both a good dressing and a low-quality product with equal probability.

Additional substances Flavorings should be included as additions to vape refills. They do not affect the efficiency of the vaping process or the characteristics of the mixture, but will allow you to add variety. For the production of self-mixing it is necessary to use only nutritional supplements

, safe for health and soluble in water.

If you have an allergy, you should not use tobacco flavoring - it is made from pepper, which is a strong allergen.

Optional components that can significantly affect the quality and properties of the mixture include:

Qhit - this substance is used to enhance the astringency of the mixture; it is especially important in the production of nicotine-free liquids.
Bitter Wizard is used to add bitterness and characteristic traditional way smoking aroma.
MTS Vape Wizard is responsible for stabilizing flavor accents, enhancing weak flavors and softening overly strong ones.

Traditional mixture formulas

Before you start preparing the liquid, you need to familiarize yourself with the basic proportions used by experienced manufacturers. In many ways, the choice of composition depends on the requirements for the final product.

Basic formulas allow beginners to simplify the task of making a mixture in the initial stages. The composition can vary depending on the wishes of the steamer and be formed based on individual preferences. There are several classic proportions that can be used without fear:

Propylene glycol + glycerin: 60-65% by 30-35% or 70% by 30% - the classic proportion of electronic liquid, the “base”, which can be used unchanged or varied to suit your own tastes.
Propylene glycol + glycerin + water: 70% to 20% to 90% to 10% - the basic formula for tobacco mixtures, produces little smoke, eliminates all sweet flavors, slightly bitter.
Propylene glycol + water: 90% to 10% or 95% to 5% - practically no vaping, but gives a strong "throat hit", great for replacing the traditional method of smoking, layering tobacco flavors or highlighting good nicotine.
Glycerin + water: 80% to 20% - light and pleasant, soft, enveloping mixture, giving a lot of steam. It doesn't hit the throat and goes well with complex aromas.
The usual “zero” is made according to the following formula: 47% propylene glycol + 47% glycerin + 6% water.

Special ones are popular among steamers. online calculators. They take into account the characteristics of the final mixture and, in accordance with them, select the required proportion of substances.

Cooking steps

The liquid production process consists of several stages. First you need to determine for yourself best formula, and then follow the instructions, adjusting them as necessary. To prepare the base, you need to select the appropriate formula and combine propylene glycol and glycerin according to the proportions. You can purchase a store-bought equivalent with a ready-made base; this will make the cooking process easier and avoid searching for missing components.

First of all, it is necessary to prepare equipment for the process: a syringe for measuring volume, a glass container or a plastic container with a tight-fitting lid, possibly a screw one, that holds 15 ml of liquid. All work should be performed with gloves, this will protect your hands from exposure to substances.

The preparation of the smoking mixture is carried out in stages:

1. Mix the liquid with distilled water.
2. Measure out the required amount of nicotine and dilute it according to the instructions and depending on the desired strength. Based on 100 ml of mixture: 0 ml – “zero”, that is, a nicotine-free mixture; 3 ml corresponds to super-light versions of classic cigarettes; 6 ml – identical to the content in light cigarettes; 12 ml – Blue or standard nicotine level; 18 ml – strong batch; 24 ml - super strong. Blends with more high content m substances are used only to dilute lighter ones; their individual consumption is dangerous to health. If the amount of nicotine is exceeded when mixing, this can be corrected by diluting the mixture with base. You can add menthol or cherry flavoring - this will not reduce the strength, but will soften the taste.
3. To get a flavorful liquid, you need to add flavoring additives. Their dosage is strictly individual and is calculated depending on the desired concentration and brand of the substance. You cannot replace food concentrates with essential oils- when burned, they decompose and cause harmful effects on the lungs, they can burn the mucous membrane. Don't add too many flavors - they can spoil the mixture. Usually 5-15 drops of flavoring per 10 ml of finished base is enough. It is better to mix the liquid with fewer flavoring additives and then adjust the flavor as you use it. If the aroma is too strong, you can add menthol flavor or dilute the liquid with a base.
4. After all the components are mixed, the container must be tightly closed and shaken, or mixed well with a spoon. The finished product should stand in a dark place for at least 12 hours, or better yet, for 24 hours. Some ready-made bases, as well as flavors (for example, from Capella Flavors) require infusion for at least 20 days according to the instructions.
5. If necessary, you can correct the properties using additional ingredients, and shake the container well again. It is advisable to shake the container for 3-4 minutes until bubbles form abundantly and acquire a whitish tint.

Homemade dressing recipes

There are both classic recipes, simulating traditional store-bought mixtures, as well as the most successful options from electronics lovers. All recipes can be repeated at home using a standard set of ingredients.

A correctly reproduced recipe will provide the rich taste and properties of the resulting substance necessary for the steamer. Options are given without taking into account companies that produce flavorings. You can take any one that suits your taste:

Nicotine-free mixture “Rainbow Summer”. Base of glycerin, water and propylene glycol - 10 ml, melon flavors - 8 drops, strawberry - 6 drops, menthol - 4 drops. If desired, you can add lemon in the amount of 4-7 drops.
"Captain Black." Base without glycerin - 10 ml, flavorings: “Coffee” - 8 drops, “Amaretto” or “Liqueur” - 3 drops, “Chocolate” - 4 drops, “Tobacco” - 4 drops.
"Fresh." Base - 10 ml, flavors: “Ice” - 4 drops, “Citrus” - 8 drops.
"Bohemian Smoke" High glycerin base - 10 ml, flavors: Irish Cream - 0.6 ml, Vanilla - 1.5 ml, Strawberry - 2.4 ml.
"Birthday". Base - 10 ml, flavors: " Apple pie" - 5 drops, "Cotton candy" - 4 drops, "Strawberries and cream" or "Blueberries" - 3 drops.

Using liquid for smoking that you prepare yourself allows you to save money. It cannot be created from scrap materials, but the initial kit costs very little, and the components included in the composition are easy to find on store shelves.

The advantages include the possibility of a unique selection of flavors and adjustment of characteristics as desired. Having gained experience in selecting aromas, you can create original liquids with a non-trivial disclosure, in no way inferior to branded products. Every vaper should try to create his own personal version of the liquid, which will solve the problem of finding the perfect refill.